Pete’s ‘76 CT70

This is a bike I picked up at the Eganville Snowmobile Show and Swap Meet in 2018.  Kind of dirty and rough, with the bonus of a creative tailpipe system.  There was no gas in it so the seller couldn’t prove it ran, therefore, a good deal was had.  I brought it inside the garage overnight, threw a new spark plug and some fuel in it and voila!  A running bike.  It’s one of those bikes with the opposite shift pattern.  Most old Honda 3 speeds were 3 down; this one’s 3 up!  Pete bought it and what a nice job he did bringing it back to life!  Any old minibike adventure stories to share, Pete?



Comments

  1. Minitrail rider7 March 2019 at 05:00

    Great site! A fun little bike for chasing the boys around the farm. A little elbow grease, carb rebuild, tank clean and a new seat and ready to rock. Might switch out the engine for a spare this spring as this one isn’t that strong.

    ReplyDelete

Post a Comment

Popular posts from this blog

Classic Mini bike Engines

Image
Making a Tecumseh Snowblower Engine Look Vintage As a kid, the Honda bikes were what we dreamed of owning.  Their motorcycle feel with steering head bearings and a transmission were high end features in a day when lawnmower type flathead engine powered mini bikes were the norm.  I remember as a kid, looking for the reel type lawnmowers that had horizontal shaft engines.  Hoping to find one no longer being used and pulling the engine off to put on a mini bike I didn’t even have at that point!  They were around in the late 60s, early 70s, but were usually 2 or 2.5 hp maximum.  My first “go kart” was one my Dad built, using parts from an old baby carriage and a sheet of plywood.  I pestered Dad until he finally conceded to find an engine to bolt onto the back of it.  I believe it was 1967 or 1968 in Ancaster when we found an old outdoor wringer washing machine engine.  Yes, gasoline powered washing machines were common up to the 1960s....
Read more

1978 CT70 Resto Mod Part 5

Image
Well, this is the final installment of this bike build.  One other thing to mention is that when fitting a 125 to a CT or and small bike chassis, the foot pegs need an hour or more of “adjustment” with some heat.  This is because the 125 is wider than the 50 or 70 engine.  The bolt pattern for fastening the foot pegs is the same though.  It just takes a bit of work to get them to clear the engine and sit level.  Finishing touches were to install the headlamp and bezel, engine oil and adjust everything.  John V. bought the bike and kept it for a couple years.  Pete bought it from him and rides it regularly.  Pics include John riding it at the sand pit near Norway Bay, being parked up at Bell’s Lake after a day of riding and it loaded with the other 1978 CT70 I fixed up.  It is a fast bike, wheelies with ease and is very reliable.
Read more

1970 Fox Minibike Part 8

Image
I saw a pitbike exhaust online for sale for about $60!  Free delivery, too.  Anyways, once the suspension was figured out, lining up the exhaust system was next. The new larger diameter pipe fit like a charm at the front, but angled upward to much to suit the vintage nature of the bike. It would appear I needed a way to bend the muffler down, but without heating or damaging the chrome on the pipe.  If I cut the pipe ahead of the factory upward bend and fit a sleeve inside the pipe, I could rotate it to the angle I needed.  So, out came the cut off tool and I began.  This would also hide the clamp and cut behind the heat shield. Once clamped and the heat shield was put back on, you’d never know it was bent upwards.  Thanks again to my friend John V for the chrome handle bar pipe and clamp! The rear brake pedal from the pit bike wouldn’t work at all on the Fox bike, so into the parts bin I dug.  I came up with a 1...
Read more